Pickups E - Guitar

Designed in the mid 70s, the 1C is our first dual coil humbucker. It has unequal windings between the coils with very warm tone, excellent treble response and very low noise and hum. The aperture is 40% wider than conventional humbuckers for warm, full lows. The unequal coil design provides more clarity in dual coil modes, and more tonal differences in single coil modes. It can be wired in series, parallel, single coils, or out-of-phase. The 1C works equally well as a neck or bridge humbucker and is often installed as pairs with the neck pickup wired in parallel and the bridge pickup wired in series.Imbalanced coils humbucker pickup for electric guitar6-string versionoriginale Bartolini humbuckerunequally wound coils for a voice between single coil und dual coilbridge positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), asymmetric field, opposite coil polarityDC resistance 4.0 kOhm each coilresonant frequency 4.4 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

The 1CTA was designed to meet the precise voice and response requirements of virtuoso Jazz guitarist Tuck Andress. It is designed to be noise-free with equal coil windings and full internal brass shielding. The design has a wide sensing aperture and offset magnetic field for brighter yet fuller voice than standard humbuckers. Since they are blade designs instead of poles, you don't need to worry about string spacing for even output level from string-to-string. They are sealed to prevent coil contamination from dust and sweat while also eliminating microphonics. Generally, the 1CTA is installed in the neck position of a Jazz guitar but is also very usable as a bridge pickup. Because of their wide frequency response and low noise, they are perfect for Jazz, but are also very popular for metal and fusion.Tuck Andress Special humbucker pickup for electric guitar6-string versionhigh fidelity, clarity, definition and articulation developed in cooperation with Tuck Andressneck positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, asymmetric ceramic blade magnets (ferrite), tight asymmetric field, opposite coil polarityDC resistance 4.3 kOhm each coilresonant frequency 4.6 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

The V88 was designed in the 80s to provide the defined, bold voice required by the genre-making guitarists of the era. It is designed to be noise-free with equal coil windings and full internal brass shielding. The design provides balance across the strings to keep the bass strings clear and strong. They are sealed to prevent coil contamination from dust and sweat while also eliminating microphonics – perfect for the stage or studio. Usually, the V88-C is installed in the neck position for brilliant treble and maximum midrange emphasis for excellent sustain. V88-C is also very usable as a bright bridge pickup. The V88-D is designed for power and sustain in the bridge position while retaining excellent balance and definition. Output level is 25% higher than V88-C. b-one humbuckers are traditional rounded-corner shape for pickguard and body-mount installations with your standard screws. Screws and other mounting hardware is not included – be sure to order what you need for your particular guitar.b-one vintage 82s humbucker pickup for electric guitar6-string versiongreat treble and midrange emphasisexcellent sustainneck positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), asymmetric field, opposite coil polarityDC resistance 4.3 kOhm each coilresonant frequency 4.6 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverbrass bracket with tapped holesdimensions (L x W x H) 69.9 x 38.6 x 24.1 mm / 2.75" x 1.52" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

The V88 was designed in the 80s to provide the defined, bold voice required by the genre-making guitarists of the era. It is designed to be noise-free with equal coil windings and full internal brass shielding. The design provides balance across the strings to keep the bass strings clear and strong. They are sealed to prevent coil contamination from dust and sweat while also eliminating microphonics – perfect for the stage or studio. Usually, the V88-C is installed in the neck position for brilliant treble and maximum midrange emphasis for excellent sustain. V88-C is also very usable as a bright bridge pickup. The V88-D is designed for power and sustain in the bridge position while retaining excellent balance and definition. Output level is 25% higher than V88-C. b-one humbuckers are traditional rounded-corner shape for pickguard and body-mount installations with your standard screws. Screws and other mounting hardware is not included – be sure to order what you need for your particular guitar.b-one vintage 82s humbucker pickup for electric guitar6-string versiongreat treble and midrange emphasisexcellent sustainbridge positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), asymmetric field, opposite coil polarityDC resistance 5.5 kOhm each coilresonant frequency 4.6 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverbrass bracket with tapped holesdimensions (L x W x H) 69.9 x 38.6 x 24.1 mm / 2.75" x 1.52" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Designed in the Grunge era, the 1D-01 is a thick and dirty humbucker. It has very good mid frequency response and wide sensing aperture for a big voice. As a pro-level pickup, it is fully sealed to be sweat-proof and alcohol-proof. The 1D-01 can be used in the neck or bridge position. In the neck position, it pairs nicely with a V94D at the bridge. In the bridge position, it pairs nicely with the V88C at the neck. The shielded 4-conductor cable is ready for coil splitting and series or parallel humbucker wiring.Deep Bright humbucker pickup for electric guitar6-string versionthick sound with good clarity and definitiongreat for Rock, Blues und Grungebridge positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, asymmetric ceramic blade magnets (ferrite), asymmetric field, opposite coil polarityDC resistance 3.5 kOhm each coilresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Designed in the Grunge era, the 1D-01 is a thick and dirty humbucker. It has very good mid frequency response and wide sensing aperture for a big voice. As a pro-level pickup, it is fully sealed to be sweat-proof and alcohol-proof. The 1D-01 can be used in the neck or bridge position. In the neck position, it pairs nicely with a V94D at the bridge. In the bridge position, it pairs nicely with the V88C at the neck. The shielded 4-conductor cable is ready for coil splitting and series or parallel humbucker wiring.Deep Bright humbucker pickup for electric guitar6-string versionthick sound with good clarity and definitiongreat for Rock, Blues und Grungebridge positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, asymmetric ceramic blade magnets (ferrite), asymmetric field, opposite coil polarityDC resistance 3.5 kOhm each coilresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassivewhite coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Designed in the Grunge era, the 3D-01 is a thick and dirty single coil. It has very good mid frequency response and wide sensing aperture for a big voice. As a pro-level pickup, it is fully sealed to be sweat-proof and alcohol-proof. The 3D-01 can be used in the neck, middle, or bridge position. In the neck position, it pairs nicely with a 3XQ in the middle and 1D-01 at the bridge. In the bridge position, it pairs nicely with the 3X at the neck and 3XQ in the middle position.Deep bright single coil pickup for electric guitar6-string versionthick, clear, well defined soundgreat for Rock, Blues, Grungebridge positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance 2.9 kOhmresonant frequency 5.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Designed in the Grunge era, the 3D-01 is a thick and dirty single coil. It has very good mid frequency response and wide sensing aperture for a big voice. As a pro-level pickup, it is fully sealed to be sweat-proof and alcohol-proof. The 3D-01 can be used in the neck, middle, or bridge position. In the neck position, it pairs nicely with a 3XQ in the middle and 1D-01 at the bridge. In the bridge position, it pairs nicely with the 3X at the neck and 3XQ in the middle position.Deep bright single coil pickup for electric guitar6-string versionthick, clear, well defined soundgreat for Rock, Blues, Grungebridge positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance 2.9 kOhmresonant frequency 5.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassivewhite coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Designed in the Grunge era, the 3D-01 is a thick and dirty single coil. It has very good mid frequency response and wide sensing aperture for a big voice. As a pro-level pickup, it is fully sealed to be sweat-proof and alcohol-proof. The 3D-01 can be used in the neck, middle, or bridge position. In the neck position, it pairs nicely with a 3XQ in the middle and 1D-01 at the bridge. In the bridge position, it pairs nicely with the 3X at the neck and 3XQ in the middle position.Deep bright single coil pickup for electric guitar6-string versionthick, clear, well defined soundgreat for Rock, Blues, Grungebridge positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, south polarityDC resistance 2.9 kOhmresonant frequency 5.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Designed in the Grunge era, the 3D-01 is a thick and dirty single coil. It has very good mid frequency response and wide sensing aperture for a big voice. As a pro-level pickup, it is fully sealed to be sweat-proof and alcohol-proof. The 3D-01 can be used in the neck, middle, or bridge position. In the neck position, it pairs nicely with a 3XQ in the middle and 1D-01 at the bridge. In the bridge position, it pairs nicely with the 3X at the neck and 3XQ in the middle position.Deep bright single coil pickup for electric guitar6-string versionthick, clear, well defined soundgreat for Rock, Blues, Grungebridge positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, south polarityDC resistance 2.9 kOhmresonant frequency 5.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassivewhite coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionneck positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance 5.5 kOhmresonant frequency 4.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionneck positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance 5.5 kOhmresonant frequency 4.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassivewhite coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup. The only thing different about this set compared to the 3X is that these have opposite polarity. Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionneck positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, south polarityDC resistance 5.5 kOhmresonant frequency 4.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup set for electric guitar6-string versionset consisting of 3X-N, 3XQ-S, 3XR-Nclear vintage soundpopular upgrade optiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance bridge 6.3 kOhmDC resistance middle 5.0 kOhmDC resistance neck 5.5 kOhmresonant frequency bridge 3.5 kHzresonant frequency middle 5.0 kHzresonant frequency neck 4.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup set for electric guitar6-string versionset consisting of 3X-N, 3XQ-S, 3XR-Nclear vintage soundpopular upgrade optiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance bridge 6.3 kOhmDC resistance middle 5.0 kOhmDC resistance neck 5.5 kOhmresonant frequency bridge 3.5 kHzresonant frequency middle 5.0 kHzresonant frequency neck 4.6 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassivewhite coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionmiddle positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, south polarityDC resistance 5.0 kOhmresonant frequency 5.0 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionmiddle positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, south polarityDC resistance 5.0 kOhmresonant frequency 5.0 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassivewhite coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionbridge positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance 6.3 kOhmresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Single coil design with full range sound and 50% more output than the stock Strat pickup. This exact replacement with extended low and high frequency response yields a warm, brilliant tone with less upper midrange emphasis than the stock pickup.Original Strat single coil pickup for electric guitar6-string versionclear vintage soundpopular upgrade optionbridge positiontrue single coilmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), narrow field, north polarityDC resistance 6.3 kOhmresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width2-conductor, shielded coaxial cable, core hotpassivewhite coverdimensions (L x W x H) 69.9 x 17.5 x 22.6 mm / 2.75" x 0.69" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Johnny Smith worked closely with Gibson to design full-bodied arch-top guitars, and we pay homage to that classic Jazz guitar sound with our own jazz pickup. The dual coil Johnny Smith (JS) humbucker gets a smooth, clear distinctive tone available with or without adjustable brackets for mounting to the end of your fretboard.Jazz guitar humbucker pickup for electric guitar6-string versionhigh fidelity, clarity, definition and articulationclassic Jazz guitar soundmounted at the end of the fretboardwith adjustable mounting bracketdual parallel humbuckingmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), wide but focused field, opposite coil polarityDC resistance 3.6 kOhm each coilresonant frequency 6.1 kHz50 mm / 1.97" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 66.0 x 28.7 x 13.7 mm / 2.6" x 1.13" x 0.54" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Johnny Smith worked closely with Gibson to design full-bodied arch-top guitars, and we pay homage to that classic Jazz guitar sound with our own jazz pickup. The dual coil Johnny Smith (JS) humbucker gets a smooth, clear distinctive tone available with or without adjustable brackets for mounting to the end of your fretboard.Jazz guitar humbucker pickup for electric guitar6-string versionhigh fidelity, clarity, definition and articulationclassic Jazz guitar soundmounted at the end of the fretboardwithout mounting bracketdual parallel humbuckingmagnetic circuit: carbon steel, brass, ceramic blade magnets (ferrite), wide but focused field, opposite coil polarityDC resistance 3.6 kOhm each coilresonant frequency 6.1 kHz50 mm / 1.97" max. sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 66.0 x 28.7 x 13.7 mm / 2.6" x 1.13" x 0.54" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

The expanded tonal range and rich harmonics of our ACE pickups are created by combining alnico V blades and ceramic bar magnets for the best of both worlds, producing the hot tone you want from an alnico pickup, balanced with the clarity you expect from ceramic. The string-to-string output is balanced by internal compensation and field shaping. The blade design ensures your tone won't fade from even the most aggressive bends. ACE Humbuckers are true pro-level pickups, so of course they are fully shielded against noise from stage lighting and studio equipment. They are sweat-proof and won't make horrible noises when you touch them like many standard bobbin-style humbuckers. They are wired with shielded 4-conductor cable for coil splitting and series or parallel humbucker wiring. Their Hot Vintage tone is great for Rock, Progressive, Funk, and Heavy Blues. ACE Humbuckers come in balanced versions for neck and bridge position.Alnico Ceramic humbucker pickup for electric guitar6-string versionhot vintage tonecombined Alnico V and ceramic magnets for full and clear voiceneck positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, copper, Alnico V blade magnets stabilized by ceramic magnets (ferrite), focused aperture, opposite coil polarityDC resistance 7.8 kOhmresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

The expanded tonal range and rich harmonics of our ACE pickups are created by combining alnico V blades and ceramic bar magnets for the best of both worlds, producing the hot tone you want from an alnico pickup, balanced with the clarity you expect from ceramic. The string-to-string output is balanced by internal compensation and field shaping. The blade design ensures your tone won't fade from even the most aggressive bends. ACE Humbuckers are true pro-level pickups, so of course they are fully shielded against noise from stage lighting and studio equipment. They are sweat-proof and won't make horrible noises when you touch them like many standard bobbin-style humbuckers. They are wired with shielded 4-conductor cable for coil splitting and series or parallel humbucker wiring. Their Hot Vintage tone is great for Rock, Progressive, Funk, and Heavy Blues. ACE Humbuckers come in balanced versions for neck and bridge position.Alnico Ceramic humbucker pickup for electric guitar6-string versionhot vintage tonecombined Alnico V and ceramic magnets for full and clear voiceneck positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, copper, Alnico V blade magnets stabilized by ceramic magnets (ferrite), focused aperture, opposite coil polarityDC resistance 7.8 kOhmresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassivechrome coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

The expanded tonal range and rich harmonics of our ACE pickups are created by combining alnico V blades and ceramic bar magnets for the best of both worlds, producing the hot tone you want from an alnico pickup, balanced with the clarity you expect from ceramic. The string-to-string output is balanced by internal compensation and field shaping. The blade design ensures your tone won't fade from even the most aggressive bends. ACE Humbuckers are true pro-level pickups, so of course they are fully shielded against noise from stage lighting and studio equipment. They are sweat-proof and won't make horrible noises when you touch them like many standard bobbin-style humbuckers. They are wired with shielded 4-conductor cable for coil splitting and series or parallel humbucker wiring. Their Hot Vintage tone is great for Rock, Progressive, Funk, and Heavy Blues. ACE Humbuckers come in balanced versions for neck and bridge position.Alnico Ceramic humbucker pickup for electric guitar6-string versionhot vintage tonecombined Alnico V and ceramic magnets for full and clear voiceneck positiondual parallel humbuckingmagnetic circuit: carbon steel, brass, copper, Alnico V blade magnets stabilized by ceramic magnets (ferrite), focused aperture, opposite coil polarityDC resistance 7.8 kOhmresonant frequency 3.5 kHz51 mm / 2.01" max. sensing width4-conductor shielded cable with bare drain wirepassivegold coverbrass bracket with tapped holesdimensions (L x W x H) 70.1 x 38.9 x 23.4 mm / 2.76" x 1.53" x 0.92" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present.