E - Bass Soapbar

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original G6 Candybar pickup for electric bass6-string versiondeep voiced and hum-cancellingclassic 90s design with input from Steve Baileyneck positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 8.8 kOhmresonant frequency 5.8 kHz65 - 100 mm / 2.56" - 3.94" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 140.2 x 23.7 x 24.1 mm / 5.52" x 0.93" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original G6 Candybar pickup set for electric bass6-string versiondeep voiced and hum-cancellingclassic 90s design with input from Steve Bailey split-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance bridge position 10 kOhmDC resistance neck position 8.8 kOhmresonant frequency bridge position 4.9 kHzresonant frequency neck position 5.8 kHz65 - 100 mm / 2.56" - 3.94" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 140.2 x 23.7 x 24.1 mm / 5.52" x 0.93" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original G6 Candybar pickup for electric bass6-string versiondeep voiced and hum-cancellingclassic 90s design with input from Steve Baileybridge positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 10 kOhmresonant frequency 4.9 kHz65 - 100 mm / 2.56" - 3.94" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 140.2 x 23.7 x 24.1 mm / 5.52" x 0.93" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original G6 Candybar pickup for electric bass7-string versiondeep voiced and hum-cancellingclassic 90s design with input from Bill Dickensneck positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 9.8 kOhmresonant frequency 5.8 kHz72 - 108 mm / 2.83" - 4.25" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 140.2 x 23.7 x 24.1 mm / 5.52" x 0.93" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original G6 Candybar pickup set for electric bass7-string versiondeep voiced and hum-cancellingclassic 90s design with input from Bill Dickenssplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance bridge position 11.1 kOhmDC resistance neck position 9.8 kOhmresonant frequency bridge position 4.9 kHzresonant frequency neck position 5.8 kHz72 - 108 mm / 2.83" - 4.25" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 140.2 x 23.7 x 24.1 mm / 5.52" x 0.93" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original G6 Candybar pickup for electric bass7-string versiondeep voiced and hum-cancellingclassic 90s design with input from Bill Dickensbridge positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 11.1 kOhmresonant frequency 4.9 kHz72 - 108 mm / 2.83" - 4.25" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 140.2 x 23.7 x 24.1 mm / 5.52" x 0.93" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Upgrade your Ibanez GWB35 or GWB20th. The 68BC5W-D3 is the same pickup as the 69GW5W-D3 used in the Ibanez Gary Willis high-end basses but in the BC shape used in the cost optimized versions. You can now get the same voice. Like the custom-made GW pickups, these have internal shielding to block radiated noise from studio equipment and stage lighting. They are passive and will work with your current electronics in most basses but are also amazing when installed with an on-board preamp – especially the Custom GW preamp – HR-2.2-IWB20. These dual coil pickups are hum-cancelling. The coils have a special structure and are arrangement tilted in 2 directions and offset from each other just like in the GW pickups. They are sealed to prevent coil contamination while also eliminating microphonics. These are truly pro-level pickups to upgrade your bass.BC Soapbar pickup for electric bass 5-string versionupgrade for Ibanez GWB35 or GWB20 same pickup as 69GW5W-D3 Gary Willis, but in BC formatdual coil, hum-cancellingmagnetic circuit: carbon steel, ceramic magnets (ferrite)DC resistance 3.5 kOhmresonant frequency 4.5 kHz68 mm / 2.7" sensing width1-conductor shielded cablepassiveblack coverdimensions (L x W x H) 100.3 x 32 x 22.6 mm x / 3.95" x 1.26" x 0.89" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

No other pickup can deliver the gigantic, luxuriant lows of Original Bart soapbars. They provide bottomless lows and low-mids, their dual coil construction eliminates the noise and muddiness that vast amounts of low-end can create. The Originals are full and warm for that vintage tone you’ve been craving, enhancing the natural voice of your bass. You’ll never find lower tones produced with higher clarity! Made for pro-level bass players, they are fully sealed and shielded making them sweat-proof, quiet if you touch them, and immune invisible noise from stage lights and studio power supplies. The cables are shielded too. Available in balanced versions for neck and bridge.Original M4 Soapbar pickup for electric bass with narrower sensing width5-string versiondeep, thick original voiceM45C-B variant for narrower string spacingneck positiondual coil parallel humbuckingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), wide aperture, opposite coil polarityDC resistance 3.9 kOhm each coilresonant frequency 4.4 kHz72 mm / 2.83" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverdimensions (L x W x H) 101.6 x 38.1 x 24,6 mm / 4.0" x 1.5" x 0.97" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

No other pickup can deliver the gigantic, luxuriant lows of Original Bart soapbars. They provide bottomless lows and low-mids, their dual coil construction eliminates the noise and muddiness that vast amounts of low-end can create. The Originals are full and warm for that vintage tone you’ve been craving, enhancing the natural voice of your bass. You’ll never find lower tones produced with higher clarity! Made for pro-level bass players, they are fully sealed and shielded making them sweat-proof, quiet if you touch them, and immune invisible noise from stage lights and studio power supplies. The cables are shielded too. Available in balanced versions for neck and bridge.Original M4 Soapbar pickup for electric bass with narrower sensing width5-string versiondeep, thick original voiceM45C-T variant for narrower string spacingbridge positiondual coil parallel humbuckingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), wide aperture, opposite coil polarityDC resistance 5,5 kOhm each coilresonant frequency 3,7 kHz72 mm / 2.83" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverdimensions (L x W x H) 101.6 x 38.1 x 24,6 mm / 4.0" x 1.5" x 0.97" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

No other pickup can deliver the gigantic, luxuriant lows of Original Bart soapbars. They provide bottomless lows and low-mids, their dual coil construction eliminates the noise and muddiness that vast amounts of low-end can create. The Originals are full and warm for that vintage tone you’ve been craving, enhancing the natural voice of your bass. You’ll never find lower tones produced with higher clarity! Made for pro-level bass players, they are fully sealed and shielded making them sweat-proof, quiet if you touch them, and immune invisible noise from stage lights and studio power supplies. The cables are shielded too. Available in balanced versions for neck and bridge.Original P2 Soapbar pickup for electric bass with narrower sensing width5-string versiondeep, thick original voicespecial version: like P25C-B, but with narrower sensing widthneck positiondual coil parallel humbuckingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), wide aperture, opposite coil polarityDC resistance 3.9 kOhm each coilresonant frequency 4.4 kHz74 mm / 2.91" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverdimensions (L x W x H) 107.7 x 31.8 x 23.9 mm / 4.24" x 1.25" x 0.94" (height incl. cable)Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goodsNote: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

No other pickup can deliver the gigantic, luxuriant lows of Original Bart soapbars. They provide bottomless lows and low-mids, their dual coil construction eliminates the noise and muddiness that vast amounts of low-end can create. The Originals are full and warm for that vintage tone you’ve been craving, enhancing the natural voice of your bass. You’ll never find lower tones produced with higher clarity! Made for pro-level bass players, they are fully sealed and shielded making them sweat-proof, quiet if you touch them, and immune invisible noise from stage lights and studio power supplies. The cables are shielded too. Available in balanced versions for neck and bridge.Original P2 Soapbar pickup for electric bass with narrower sensing width5-string versiondeep, thick original voicespecial version: like P25C-T, but with narrower sensing widthbridge positiondual coil parallel humbuckingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), wide aperture, opposite coil polarityDC resistance 5.5 kOhm each coilresonant frequency 3.7 kHz74 mm / 2.91" max. sensing width4-conductor shielded cable with bare drain wirepassiveblack coverdimensions (L x W x H) 107.7 x 31.8 x 23.9 mm / 4.24" x 1.25" x 0.94" (height incl. cable)Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present.Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Classic Bass Candybars have a rich, deep voice with lots of high-end clarity and warmth with enhanced treble response and higher output than our Original Candybars. When you dig in, they are responsive and growly. When you pull back, they are clear and sweet. And they'll take any slapping and popping you want to give them. The Classic Bass series is popular with progressive, jazz, gospel, and metal musicians where articulation is critical. Classic Bass Candybars are sweat-proof and won't make horrible noises when you touch them or hit them with the strings. They are passive and will work with your current electronics in most basses. These inline dual coil pickups are hum-cancelling even when only playing the neck or bridge pickup, so they are well suited for studio or stage. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Classic Bass X4 Candybar pickup set for electric bass5-string versionenhanced treble output for refined jazz bass applicationshum-cancelling designneck positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), focused aperture, opposite polarity for bass and treble coils for neck and bridge pickupsDC resistance 9.5 kOhmresonant frequency 5.1 kHz60 - 76 mm / 2.36" - 3.99" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Classic Bass Candybars have a rich, deep voice with lots of high-end clarity and warmth with enhanced treble response and higher output than our Original Candybars. When you dig in, they are responsive and growly. When you pull back, they are clear and sweet. And they'll take any slapping and popping you want to give them. The Classic Bass series is popular with progressive, jazz, gospel, and metal musicians where articulation is critical. Classic Bass Candybars are sweat-proof and won't make horrible noises when you touch them or hit them with the strings. They are passive and will work with your current electronics in most basses. These inline dual coil pickups are hum-cancelling even when only playing the neck or bridge pickup, so they are well suited for studio or stage. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Classic Bass X4 Candybar pickup set for electric bass5-string versionenhanced treble output for refined jazz bass applicationshum-cancelling designsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), focused aperture, opposite polarity for bass and treble coils for neck and bridge pickupsDC resistance bridge position 10.8 kOhmDC resistance neck position 9.5 kOhmresonant frequency bridge position 4.2 kHzresonant frequency neck position 5.1 kHz60 - 76 mm / 2.36" - 3.99" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Classic Bass Candybars have a rich, deep voice with lots of high-end clarity and warmth with enhanced treble response and higher output than our Original Candybars. When you dig in, they are responsive and growly. When you pull back, they are clear and sweet. And they'll take any slapping and popping you want to give them. The Classic Bass series is popular with progressive, jazz, gospel, and metal musicians where articulation is critical. Classic Bass Candybars are sweat-proof and won't make horrible noises when you touch them or hit them with the strings. They are passive and will work with your current electronics in most basses. These inline dual coil pickups are hum-cancelling even when only playing the neck or bridge pickup, so they are well suited for studio or stage. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Classic Bass X4 Candybar pickup set for electric bass5-string versionenhanced treble output for refined jazz bass applicationshum-cancelling designbridge positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), focused aperture, opposite polarity for bass and treble coils for neck and bridge pickupsDC resistance 10.8 kOhmresonant frequency 4.2 kHz60 - 76 mm / 2.36" - 3.99" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Classic Bass Candybars have a rich, deep voice with lots of high-end clarity and warmth with enhanced treble response and higher output than our Original Candybars. When you dig in, they are responsive and growly. When you pull back, they are clear and sweet. And they'll take any slapping and popping you want to give them. The Classic Bass series is popular with progressive, jazz, gospel, and metal musicians where articulation is critical. Classic Bass Candybars are sweat-proof and won't make horrible noises when you touch them or hit them with the strings. They are passive and will work with your current electronics in most basses. These inline dual coil pickups are hum-cancelling even when only playing the neck or bridge pickup, so they are well suited for studio or stage. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Classic Bright Tone Bass X4 Candybar pickup set for electric bass - 5-string version - enhanced treble output for refined jazz bass applications - hum-cancelling design - split-coil, dual inline hum-killing - magnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), focused aperture, opposite polarity for bass and treble coils for neck and bridge pickups - 60 - 76 mm / 2.36" - 3.99" sensing width - 2-conductor, shielded coaxial cable, core hot - passive - black cover - dimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original X4 Candybar pickup for electric bass5-string versiondeep voiced and hum-cancellingpopular choice for refined jazz bass applicationsneck positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 8 kOhmresonant frequency 5.8 kHz60 - 76 mm / 2.36" - 2,99" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original X4 Candybar pickup set for electric bass5-string versiondeep voiced and hum-cancellingpopular choice for refined jazz bass applicationssplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance bridge position 8.6 kOhmDC resistance neck position 8 kOhmresonant frequency bridge position 4.9 kHzresonant frequency neck position 5.8 kHz60 - 76 mm / 2.36" - 2,99" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original X4 Candybar pickup for electric bass5-string versiondeep voiced and hum-cancellingpopular choice for refined jazz bass applicationsbridge positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 8.6 kOhmresonant frequency 4.9 kHz60 - 76 mm / 2.36" - 2,99" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 105.2 x 22.0 x 24.1 mm / 4.14" x 0.87" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original X5 Candybar pickup for electric bass5-string versiondeep voiced and hum-cancellingpopular choice for custom refined jazz bass applicationsneck positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 7.9 kOhmresonant frequency 5.8 kHz 60 - 80 mm / 2.36" - 3.15" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 119.3 x 21,6 x 24.6 mm / 4.7" x 0.85" x 0.97" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original X5 Candybar pickup set for electric bass5-string versiondeep voiced and hum-cancellingpopular choice for custom refined jazz bass applicationssplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance bridge position 8.7 kOhmDC resistance neck position 7.9 kOhmresonant frequency bridge position 4.9 kHzresonant frequency neck position 5.8 kHz60 - 80 mm / 2.36" - 3.15" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 119.3 x 21,6 x 24.6 mm / 4.7" x 0.85" x 0.97" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you've been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early '70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate "microphonics" - the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups.Original X5 Candybar pickup for electric bass5-string versiondeep voiced and hum-cancellingpopular choice for custom refined jazz bass applicationsbridge positionsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, ceramic blade magnets (ferrite), opposite polarity for neck and bridge pickupsDC resistance 8.7 kOhmresonant frequency 4.9 kHz60 - 80 mm / 2.36" - 3.15" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 119.3 x 21,6 x 24.6 mm / 4.7" x 0.85" x 0.97" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Based on our legendary Original series J-Bass pickups with dual-inline, split coils, these pickups cancel hum while providing that full and warm vintage tone you’ve been craving, enhancing the natural voice of your bass. Original Barts bring out your voice, low and clear. In the early ‘70s, Bill Bartolini leveraged his deep knowledge of acoustics to create pickups that produce the most natural, musical voice from the instrument. He added shielding to block radio signals and noise. He developed a method of sealing, isolating, and stabilizing the coils so they could be encapsulated in epoxy to eliminate “microphonics” – the nasty noise you get when you touch typical pickups. Candybar shapes were made for refined Jazz bass builders who wanted to avoid the routing hassles and busy look of standard J-Bass pickups. Available in versions for neck (Bass, -B) and bridge (Treble, -T).Original Bass X6 Candybar pickup set for electric bass6-string versiondeep voiced for refined jazz bass applicationshum-cancelling designsplit-coil, dual inline hum-killingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), opposite polarity for bass and treble coils for neck and bridge pickupsDC resistance bridge position 10.0 kOhmDC resistance neck position 8.8 kOhmresonant frequency bridge position 4.9 kHzresonant frequency neck position 5.8 kHz65 - 96 mm / 2.56" - 3.78" sensing width2-conductor, shielded coaxial cable, core hotpassiveblack coverdimensions (L x W x H) 130.0 x 21.0 x 24.1 mm / 5.1" x 0.82" x 0.95" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Classic Bass soapbars make you sound better, so you play better. They have a rich, deep voice with lots of high-end clarity and warmth. When you dig in, they are responsive and growly. When you pull back, they are clear and sweet. And they'll take any slapping and popping you want to give them. The Classic Bass series is popular with progressive, jazz, gospel, and metal musicians where articulation is critical. Without sacrificing low-end, Classic Bass pickups are sweat-proof and won't crackle and thud when you touch them or hit them with the strings. If you play a wide variety of music, you know you need some pro-level pickups, but you don't want to do a big upgrade project, Classic Bass pickups are a great choice. They are passive and will work with your current electronics in most basses. There are different versions for neck and bridge so they balance well in your bass.Classic Bass BB Soapbar pickup for electric bass4-string versionversatile classic bass voicingsmallest available bass soapbar shapeneck positiondual coil parallel humbuckingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), focused aperture, opposite coil polarityDC resistance 3.7 kOhm each coil resonant frequency 4.9 kHzmax. 60 mm / 2.36" sensing width4-conductor shielded cable with bare drain wirepassiveblack coverdimensions (L x W x H) 86.9 x 35.6 x 23.1 mm / 3.42" x 1.4" x 0,91" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present. 

Classic Bass soapbars make you sound better, so you play better. They have a rich, deep voice with lots of high-end clarity and warmth. When you dig in, they are responsive and growly. When you pull back, they are clear and sweet. And they'll take any slapping and popping you want to give them. The Classic Bass series is popular with progressive, jazz, gospel, and metal musicians where articulation is critical. Without sacrificing low-end, Classic Bass pickups are sweat-proof and won't crackle and thud when you touch them or hit them with the strings. If you play a wide variety of music, you know you need some pro-level pickups, but you don't want to do a big upgrade project, Classic Bass pickups are a great choice. They are passive and will work with your current electronics in most basses. There are different versions for neck and bridge so they balance well in your bass.Classic Bass BB Soapbar pickup for electric bass4-string versionversatile classic bass voicingsmallest available bass soapbar shapebridge positiondual coil parallel humbuckingmagnetic circuit: carbon steel, brass, copper, ceramic blade magnets (ferrite), focused aperture, opposite coil polarityDC resistance 5.1 kOhm each coil resonant frequency 4.5 kHzmax. 60 mm / 2.36" sensing width4-conductor shielded cable with bare drain wirepassiveblack coverdimensions (L x W x H) 86.9 x 35.6 x 23.1 mm / 3.42" x 1.4" x 0,91" (height incl. cable)Note: Replacement pickups may differ slightly in shape and dimensions from the original pickups. Adjustments may be necessary. It is recommended that you check the schematic drawings carefully. Deviations in the size and shape of the pickups do not constitute grounds for complaint. Screws and springs are not included. Due to the manufacturing process, the plastic housings of Bartolini pickups may show minor processing or handling marks. The cable ends of some pickups may also be pre-soldered. These characteristics do not constitute grounds for complaint or reason for return. Note: The return and refund policy does not apply to pickups, if their cables have been cut or soldered, or other damage affecting the condition of the goods is present.