Signal Routing Splitter

Greetings sonic explorers! EarthQuaker Devices have crafted the One to Four Splitter to route your next musical adventure and help create sounds you never thought possible. This One to Four Splitter allows the user to take one input and send it through four buffered outputs for unlimited creative potential. Use it to run out to four amps to play in quadraphonic sound and blow people’s minds. Send a clean signal to your DAW and another through your normal signal chain to have a clean back up while recording. Run 2 parallel stereo signal paths! Use the One to Four splitter together with the Four to One Mixer to create wild parallel signal chains! Use the Buffer/Splitter and run 2 x One to Four Splitters to have 8 parallel paths!!! This device features a unity gain buffer on each output for maximum punch and clarity. These buffered outputs have a flat frequency response with a high 1MOhm input impedance and a low 100 Ohm output impedance. This ensures that your signal won’t lose any quality and will sound just like you intended. Even long cable runs are no match for the One to Four Splitter. Like EarthQuaker Devices other products, the One to Four Splitter is made at EarthQuaker Devices factory in Akron, Ohio. With the One To Four Splitter, the possibilities are nearly endless.signal buffer / preampprevents sound loss with long cable runs or in signal chains with many true bypass pedalssignal is split internally and routed to vier separate outputsinput impedance 1 MOhmoutput impedance 100 Ohmstatus LEDmetal housing6.3 mm mono jack input4x 6.3 mm mono jack outputpower supply via optional 9V DC adapter, 2.1 x 5.5 mm barrel plug, polarity (-) centerbattery operation not supportedcurrent draw 15 mAdimensions (L x W x H) 121 x 64 x 38 mm / 4.75" x 2.5" x 1.5"weight 230 g / 0.52 lbshand made in USA

The EarthQuaker Devices Passive ABY box is the perfect solution if you can’t decide when and where you would like your signal to go. In its most basic form, this passive little box is commonly used to run a single input out to two destinations and lets you choose between using either individually or both at the same time. The most common problem and ABY is used to solve is one input being sent to out to two amplifiers but it doesn’t have to stop there! Because of its completely passive circuitry it can also be used in reverse to choose between two inputs to a single output. Use it to simultaneously run two different instruments to one source input! An oboe and a bass, a keyboard and a harmonica, a lute and a modular synth… you know, whatever! This compact little device has a small footprint and won’t take up much real estate on your board and is built using high quality parts that will withstand years of use and keep going.A/B/Y Switcher / Splitterideal for routing instruments, amps, effects, speaker cabinets etc.made from high-quality and durable partstwo different modes available: A/B - Y and A&B - Yinputs and outputs can be used in both directionsallows switching one input signal to two outputs or two input signals to one outputallows splitting the signal to two outputsallows merging two signals to one outputTrue BypassY and A/B footswitchstatus LEDsmetal housing6.3 mm mono jack input / outputpower supply via optional 9V DC adapter, 2.1 x 5.5 mm barrel plug, polarity (-) centerbattery operation not supportedcurrent draw 60 mAdimensions (L x W x H) 113 x 73 x 48 mm / 4.4375" x 2.875" x 1.875"weight 231 g / 0.32 lbshand made in USA

A buffer is an important tool to combat tone loss with long cable runs or in signal chains running lots of true bypass pedals. The EarthQuaker Devices Buffer/Splitter uses the same great high 1 Mohm input impedance and low 100 ohm output impedance found in our Buffer/Preamp to restore your tonal integrity! This buffer is designed to both maintain high end and give your low end a subtle, yet powerful, little kick for some added dimension! What’s better than a single output buffer? A dual output buffer, that’s what! Use the EarthQuaker Devices Buffer/Splitter to split your signal into two and send them anywhere you like! Two amps! Turn a mono signal into a stereo signal! Send one output to your effects and use the other as a dry-through! Remove your tuner from the signal path… you get the idea!signal buffer / preampprevents sound loss with long cable runs or in signal chains with many true bypass pedalssignal is split internally and routed to two separate outputsinput impedance 1 MOhmoutput impedance 100 Ohmstatus LEDmetal housing6.3 mm mono jack input2x 6.3 mm mono jack outputpower supply via optional 9V DC adapter, 2.1 x 5.5 mm barrel plug, polarity (-) centerbattery operation not supportedcurrent draw 15 mAdimensions (L x W x H) 94 x 41 x 35 mm / 3.6875" x 1.625" x 1.375"weight 129 g / 0.285 lbshand made in USA

The JHS Pedals Active A/B/Y is the perfect solution when you need to send one signal to two outputs with the ability to choose either output (or both) on the fly. Just plug in your instrument cable (or patch cable) into the input, then use the outputs to send signal to any combination of amplifiers, interfaces, mixing board, or anywhere else you want to send your signal. Because the Active A/B/Y has an output transformer on one of the outputs, there is no need for a ground lift as the transformer eliminates any hum. FET transistors for completely silent switching and the capability to use one or both outputs simultaneously, the JHS Pedals Active A/B/Y will be the one pedal that you can never leave home without!A/B/Y switcher / splitteractive operationoutput transformer eliminates hum - no ground lift requiredFET transistors for silent switchingPolarity reversal switch (Channel A)AB footswitchY footswitchstatus LEDsmetal housing6.3 mm mono input jack2 x 6.3 mm mono output jackpower supply via optional 9V DC adapter, 2.1 mm x 5.5 mm barrel plug, polarity negative (-) centerbattery operation not supportedcurrent draw 47 mAdimensions (W x D x H) 112 x 60 x 31 mm / 4.42" x 2.38" x 1.22"weight 220 g / 0.49 lbs made in USA

Need to split your signal? Don’t want to settle for a passive device that will kill your tone and cause signal loss? This is what you need! This little box of magic takes your input signal and splits it into two always-on outputs that are buffered so you don’t lose clarity or tone in any way. Plug your guitar in and use one output to send your clean signal somewhere like a tuner, mixer, separate amp, etc... and send the other output through your board like normal.signal splittersplits the input signal permanently in 2 output signalsno signal degradation or volume lossbuffered signal pathstatus LEDmetal housing6.3 mm mono IN jack2 x 6.3 mm OUT jackspower supply via optional 9V DC adapter 2.1 mm x 5.5 mm barrel plug, polarity (-) centerbattery operation not supportedcurrent draw less than 100 mAdimensions (L x W x H) 47 x 95 x 35 mm / 1.85" x 3.74" x 1.37"weight 120 g / 0.26 lbs made in USA

AB/Y switcher and signal splitter A/B or A&B to Y mode switchon/off footswitchstatus LED (A: red, B: blue, Y: pink) 3 in-/outputs A/B/Y6,3 mm mono jackoptional AC adapter 9V DC (center minus plug)can be used w/o power supply (LED stays off) metal housingdimensions (L x W x H) 93.5 x 42 x 52 mm / 3.68" x 1.65" x 2.04"weight 160 g / 0.35 lbs

The One Control BJF Buffer Split has multiple functions which makes it an extremely versatile utility box to have on your pedalboard. It combines the functions of the 1 Loop Box and AB Box with a switchable buffer. The BJF Buffer Split can be used as A/B switch, true bypass loop switcher, splitter or even as an input selector. The side-mounted switches protect the settings from unwanted changes and the switchable buffer prevents signal loss at long signal paths or large effect setups.A/B switch, true bypass looper and splitter for effects pedalshigh-quality BJF buffer circuit prevents signal loss at long signal paths or large effect setupstrue bypassSPLIT/1LOOP or FS/AB BOX switchBuffer on/off switchmulti-function footswitchstatus LEDmetal housing6.3 mm mono in / output jacks6.3 mm mono send / return jackspower supply via optional 9V DC adapter, 2.1 x 5.5 mm barrel plug, polarity (-) centerpassive operation without power supply possible (status LEDs and buffer without function)battery operation not supportedcurrent draw 3 mAdimensions (L x W x H) 101 x 53 x 49 mm / 3.98" x 2.09" x 1.93"weight 150 g / 0.33 lbs

A/B/Y Switcher / SplitterIdeal for routing line signals from instruments to amps or effectstwo different modes available: A/B - Y and A&B - Yinputs and outputs can be used in both directionsallows switching one input signal to two outputs or two input signals to one outputallows splitting the signal to two outputsallows merging two signals to one outputTrue Bypassmode selector switchchannel footswitchstatus LED (red, blue, pink)aluminum housing6.3 mm mono jack input / outputpower supply via optional 9V DC adapter, 2.1 x 5.5 mm barrel plug, polarity (-) centerbattery operation not supportedcurrent draw 8 mAoperation without power source possible (LED then without function)dimensions (L x W x H) 92 x 42 x 52 mmweight 145 g